Wood is still the most popular choice for land owners and the care it needs a minimum of effort. Unlike laminate or engineered wood, wood can be painted many times, and add years of beauty and warmth to your home and increase its value and rate of resale. The current floor care is needed to maintain his tough look great, however, and there are four main aspects of wood floor care:
1. Cleaning hardwood floors
2. The repair hardwood floor
3. Refinishing hardwood floor
4. Protection of hardwood floors
Regularly clean your wood
Learn how to clean wood floors is important because the bane of hardwood is dirt and dust, which marks the beginning and the floor if not removed immediately. In addition, dust is more easily seen in the wooden floors of what's on linoleum or carpet, especially in sunlight and, particularly if the soil has a dark stain. Caring for hardwood floors, therefore, means sweeping and dusting regularly - once a week, at least, and after any event that leaves dirt and dust behind. Regular household dusting and cleaning products cause harm, however, and you should use only products specifically designed for hardwood. Vacuuming is preferable to sweeping because it allows the dust and dirt that was removed from the tables, but use a vacuum with a mesh of bare ground, and not a beater bar, which can damage the wood.
When a more thorough cleaning is necessary, use a cleaning method suitable for finishing your floor. If the floor has a glossy finish, which means that polyurethane, urethane or a water base, or a similar finish has been used to form a protective barrier on the hardwood. If you have a matte finish, which means that the floor is protected with a penetrating seal oil and / or wax. In none of these finishes is the water an acceptable cleaning agent, but both can accept a surface moisture clean sweep, which means that the MOP is not wet, only damp to the touch. You are only cleaning the surface and do not use enough water to penetrate to the wood oiled and waxed. When using a damp mop on wood oil and wax, can add a little neutral pH cleaner for hardwood floors water before dipping the mop in it. A floor with a glossy protective barrier can accept a generic wood floor cleaner if it contains no wax or oil.
The prohibitions are as important as making the wood floor care;
1. Do not use ammonia, regular floor cleaners, household cleaners, powdered products or hardwood.
2. Never use wax on a polyurethane floor with a glossy finish or others.
3. Never wash the hardwood, using only slightly damp mop.
Repair any damage to your floors as soon as possible
In most cases, damage to the surface when oil and wax hardwood floors have suffered, you have to remove the finish with a wax or oil extractor before dealing with the damage. After completing the repair, re-wax or re-oil the area. Surface damage occurs less frequently in wood protected by polyurethane or a similar type of sealant, and when it does, the damage is not so obvious. When the repair of floors such finishes, strip the finish from the entire board or boards where the damage occurred. Make your repairs and then apply a finishing product advice that is consistent with the rest of the floor.
1. Watermarks: Remove the protective finish, rub the marks with fine steel wool grade. Repeat if necessary, cleaned and then Refinish.
2. Scorch marks: Lightly sand the surface, use a damp cloth to pick up the grain, and then refinish as desired.
3. Scratches and gouges: Hide superficial scratches with matching wood putty or caulk. After the area is dry, sand and refinish.
Wear your refinishing wood floors will resume their original beauty and value
In a house with a rickety wooden floors, the biggest improvement you can do is refinish the floors. Start by making necessary repairs, and then remove all furniture and curtains and close the vents and registers in the room so that dust does not spread through the house. Sanding floors is easiest to do with a drum sander and a machine side edges and corners of the room. You can rent these machines, and is a good idea to rent a floor buffer or polisher at the same time. Plan to make three passes with your sanding equipment, using sandpaper growing increasingly thin. Vacuum thoroughly and collect every bit of fine-grained powder with tacking cloths. All the dust and dirt must be removed. Now you can apply a stain if you wish, you can let the natural color and design of wood - as the popular oak, maple, cherry or - to be displayed.
Poland and clean dust and dirt from the floor again, and then apply the sealant - or a water-based polyurethane polyurethane that provides a protective barrier, or oil and wax, which penetrates the wood and protects from within. Carefully read all the information that accompanies each product, follow the safety warnings and applied many coats of stain or sealer as suggested by the manufacturer of the products they are using.
Wood floor care means providing ongoing protection floor
Just as regular cleaning, repair and refinishing, as needed, a number of protective measures you can take to preserve the beauty of the wood:
1. Use rugs and mats in high traffic areas and sites of frequent spills (eg, in front of the stove, sink and refrigerator). Move these rugs frequently so that these areas of the plant remains the same color as the soil exposed. Furthermore, it is best to choose cotton rugs, since they do not hold water under them like rubber or vinyl could.
2. Keep high heels in good condition and avoid the use of stiletto heels.
3. Keep nails trimmed on pets.
4. Clean up spills immediately with a paper towel or dry cloth. A damp cloth can be used for sticky spills, but dry the spot immediately afterwards with another towel or cloth.
5. Lift rather than drag furniture when moving and using sense contacts under furniture legs to prevent scratches and gouges.
6. Use blinds or sheer curtains to protect their soil discoloration caused by direct sunlight.
With proper care and maintenance, wooden floors retain their beauty and enhance any decor you choose. When the floors are worn, or if damaged, can be restored to its former glory, with a little time, effort and money. Use the Internet to check the quality of products, read the information on how to use it to compare prices and place orders. We can help with all your needs for wood floor care - all wood flooring discount wood cleaners - and all items can be purchased online and delivered to your door. Let us help you keep your hardwood floors looking their best.
Making homemade Fresh sausages
Wednesday, February 10, 2010
Thursday, February 4, 2010
Glue Down Installing Hardwood Flooring
The queue for establishing the method of wood floors is one of the original methods of installing hardwood floors. If you want to learn the basics of how to install hardwood flooring using the glue by method, you have come to the right place.
Among do it yourself wood floor, which are made with the tail by the method may be the most stable and durable. When you are installing hardwood flooring using the glue by method, you can be sure you are using a technique that has been proven over time.
Tools required for installing hardwood floors
Square notched trowel - This palette should have a quarter-inch sides for the implementation of the queue.
Broom and Dust Pan - You want to be constantly cleaning the saw dust could be trapped in the panels of floor or get stuck in your connecting joints. The last thing we need is a hardwood floor packages when finished installing wood floors.
Carpenter's Pencil - This is what you use to mark where to make cuts in its panels. You can also use this to mark the area where it will be by panels. You will want to maintain this practice at all times, since it is especially important with the glue for the method that everything be done with much accuracy.
Circular Saw - You'll use your circular saw to cut panels as necessary. In addition, you'll use your circular saw to score your substrate sheets every eight inches. This is important for preventing curling panels.
Glue - Wood panel kits Many come with their own queue. If you need to buy glue for wood panels, I recommend Bostik Best adhesive.
Lace Nails - We'll use these nails to connect the panels to walls and wall strips.
Plywood Substrate Sheets - These are placed on top of concrete and go under your wood floor.
Soft cloth - You will need these to clean the excess glue around the process of installing hardwood floors. If the glue is allowed to set, it will take additional steps to eliminate it. In some cases, require special chemicals and glue to remove glue, once it has set. You will also need to clean your clothes soft after you've installed your hardwood floors.
RUBBER GLOVES - is far better to stick the fingers of the gloves, with their own fingers together! And many people do not like having dried glue on their hands for several weeks after completing the installation of hardwood floors.
Final preparation of installing hardwood floors
When using the glue for the installation method of hardwood flooring, is absolutely essential that the surface where it is putting your flooring panels are properly prepared.
You will connect your flooring panels on this surface, so that the floor should be smooth, dry and as clean as possible to give your hardwood floor solid support base. Take special care to clean anything that seems likely to be fat or oil, as its tail can not properly bond.
It is also very important that your sub floor be completely level and flat. If you notice any irregularity, get some concrete patches in the hardware store to match the sub floor.
You must also choose one of two methods of wooden paneling down with adhesive per method. Your options for installing wood floors are the ride of the method or the wet method Lay.
If you choose the wet application method for installing hardwood floors, will be putting glue around the substrate followed by the placement of the wooden panel on the top of the queue. After the glue begins to be in poor taste to continue with the next panel.
However, sometimes it is recommended to first time installers use the method to put glue on the following panels before the glue becomes tacky so you can adjust your panels a few minutes later if not aligned properly.
The Walk The method of installing hardwood flooring requires the panel laying accurate. This process of installing hardwood floors waiting until the glue is very sticky and then set the panel on the tail. This keeps you from getting spots of glue on all the panels on the fly.
Hardwood installers with experience often use the Walk On method because of the better finished results it can provide. Since you are reading the instructions on how to install hardwood floors, assume that you are using the wet method Lay.
Instructions for Installing Hardwood Floors
1. Place your substrate sheets, stretched across the foundation. Make sure the surface is level, clean and free of debris.
2. Get your hot glue. Should be slightly above room temperature or it will be very difficult to work. If it is below the ambient temperature, it will be impossible to work with his tail.
3. Use your square notched trowel to put glue on the starting corner of the room. Put enough to securely fasten the board, but the ration queue in order to be able to complete the entire process of hardwood floors.
If there was any doubt about whether you have enough glue, would be a good idea to buy more before you start pasting. Usually you will find that it takes a day to make the floor when you lose your tail before it's over.
4. Try to place the wood panel top to bottom in the tail, was secured in the corner. Since you're working with wet glue, place the panel as best you can in the beginning to the queue will not run around as adjust the placement of the panel. If he had used the walk method would not be able to move the panel all within seconds after placement.
5. You can continue as in the previous steps with the addition of more groups until the last panel, not to be fully fit. Use your pencil to mark where to cut the board and saw to make the cut.
6. Get your first row wedge, very hard to provide a solid foundation for its entire plant.
7. Before any of the glue dries, use a soft cloth to clean any glue that may be sitting on the surface of the front row. The longer you wait to clean the glue, the harder it will get to clean the glue.
8. Hopefully not maul the top of the panel piece that you cut to stop the front row. That will be the panel that is used to start the next row. This helps ensure that your hardwood floor looks nice by having all the panels of displacement.
9. If you are watching the bubbles, hills, slopes or on the panels that has been made, put a heavy flat object on top of these sections to keep them until the glue is attached to the substrate.
10. Clean again. Get all the sawdust and glue away. A soft cloth with mineral spirits that can be used to get glue you've missed that may be hardening. Clean the mineral spirits off quickly to avoid damaging the floor. You must have a nice new wooden floor.
Hindsight Tips for Installing hardwood flooring:
For best results, use plywood sheets to form the substrate.
The thicker the substrate of the leaves, the easier it is to compensate for the leveling of differences in the surface. But even should try to get the surface as level as possible before putting your sheets of substrate.
If you have enough flat, heavy objects, place them in each new group as placing the panel on the ground to help the optimum fixation to the substrate. Do not use anything that might damage the surface of the panels. If you have nothing else, you can always put in the panels. Be careful not to get glue on top of them though.
Be sure that you have made a good choice of Installing Hardwood Floors
Once you have your wood flooring glued, you're ready to experience a great sense of accomplishment. If you did a good job of installing the hardwood floor with adhesive by method, not experience nearly as creaky floor syndrome as you would with other installation methods.
And for their sake, I hope you followed the instructions carefully and choose high quality soils. This is due to the substitution of a glued wood floor is not a task for amateurs. That is unless you pleasure destructive tendencies. You'll need some serious hammer, crow bar, and circular saw work, if you ever want to replace the glued wood floor.
Why choose Full Coverage Auto Insurance For Your Car
Among do it yourself wood floor, which are made with the tail by the method may be the most stable and durable. When you are installing hardwood flooring using the glue by method, you can be sure you are using a technique that has been proven over time.
Tools required for installing hardwood floors
Square notched trowel - This palette should have a quarter-inch sides for the implementation of the queue.
Broom and Dust Pan - You want to be constantly cleaning the saw dust could be trapped in the panels of floor or get stuck in your connecting joints. The last thing we need is a hardwood floor packages when finished installing wood floors.
Carpenter's Pencil - This is what you use to mark where to make cuts in its panels. You can also use this to mark the area where it will be by panels. You will want to maintain this practice at all times, since it is especially important with the glue for the method that everything be done with much accuracy.
Circular Saw - You'll use your circular saw to cut panels as necessary. In addition, you'll use your circular saw to score your substrate sheets every eight inches. This is important for preventing curling panels.
Glue - Wood panel kits Many come with their own queue. If you need to buy glue for wood panels, I recommend Bostik Best adhesive.
Lace Nails - We'll use these nails to connect the panels to walls and wall strips.
Plywood Substrate Sheets - These are placed on top of concrete and go under your wood floor.
Soft cloth - You will need these to clean the excess glue around the process of installing hardwood floors. If the glue is allowed to set, it will take additional steps to eliminate it. In some cases, require special chemicals and glue to remove glue, once it has set. You will also need to clean your clothes soft after you've installed your hardwood floors.
RUBBER GLOVES - is far better to stick the fingers of the gloves, with their own fingers together! And many people do not like having dried glue on their hands for several weeks after completing the installation of hardwood floors.
Final preparation of installing hardwood floors
When using the glue for the installation method of hardwood flooring, is absolutely essential that the surface where it is putting your flooring panels are properly prepared.
You will connect your flooring panels on this surface, so that the floor should be smooth, dry and as clean as possible to give your hardwood floor solid support base. Take special care to clean anything that seems likely to be fat or oil, as its tail can not properly bond.
It is also very important that your sub floor be completely level and flat. If you notice any irregularity, get some concrete patches in the hardware store to match the sub floor.
You must also choose one of two methods of wooden paneling down with adhesive per method. Your options for installing wood floors are the ride of the method or the wet method Lay.
If you choose the wet application method for installing hardwood floors, will be putting glue around the substrate followed by the placement of the wooden panel on the top of the queue. After the glue begins to be in poor taste to continue with the next panel.
However, sometimes it is recommended to first time installers use the method to put glue on the following panels before the glue becomes tacky so you can adjust your panels a few minutes later if not aligned properly.
The Walk The method of installing hardwood flooring requires the panel laying accurate. This process of installing hardwood floors waiting until the glue is very sticky and then set the panel on the tail. This keeps you from getting spots of glue on all the panels on the fly.
Hardwood installers with experience often use the Walk On method because of the better finished results it can provide. Since you are reading the instructions on how to install hardwood floors, assume that you are using the wet method Lay.
Instructions for Installing Hardwood Floors
1. Place your substrate sheets, stretched across the foundation. Make sure the surface is level, clean and free of debris.
2. Get your hot glue. Should be slightly above room temperature or it will be very difficult to work. If it is below the ambient temperature, it will be impossible to work with his tail.
3. Use your square notched trowel to put glue on the starting corner of the room. Put enough to securely fasten the board, but the ration queue in order to be able to complete the entire process of hardwood floors.
If there was any doubt about whether you have enough glue, would be a good idea to buy more before you start pasting. Usually you will find that it takes a day to make the floor when you lose your tail before it's over.
4. Try to place the wood panel top to bottom in the tail, was secured in the corner. Since you're working with wet glue, place the panel as best you can in the beginning to the queue will not run around as adjust the placement of the panel. If he had used the walk method would not be able to move the panel all within seconds after placement.
5. You can continue as in the previous steps with the addition of more groups until the last panel, not to be fully fit. Use your pencil to mark where to cut the board and saw to make the cut.
6. Get your first row wedge, very hard to provide a solid foundation for its entire plant.
7. Before any of the glue dries, use a soft cloth to clean any glue that may be sitting on the surface of the front row. The longer you wait to clean the glue, the harder it will get to clean the glue.
8. Hopefully not maul the top of the panel piece that you cut to stop the front row. That will be the panel that is used to start the next row. This helps ensure that your hardwood floor looks nice by having all the panels of displacement.
9. If you are watching the bubbles, hills, slopes or on the panels that has been made, put a heavy flat object on top of these sections to keep them until the glue is attached to the substrate.
10. Clean again. Get all the sawdust and glue away. A soft cloth with mineral spirits that can be used to get glue you've missed that may be hardening. Clean the mineral spirits off quickly to avoid damaging the floor. You must have a nice new wooden floor.
Hindsight Tips for Installing hardwood flooring:
For best results, use plywood sheets to form the substrate.
The thicker the substrate of the leaves, the easier it is to compensate for the leveling of differences in the surface. But even should try to get the surface as level as possible before putting your sheets of substrate.
If you have enough flat, heavy objects, place them in each new group as placing the panel on the ground to help the optimum fixation to the substrate. Do not use anything that might damage the surface of the panels. If you have nothing else, you can always put in the panels. Be careful not to get glue on top of them though.
Be sure that you have made a good choice of Installing Hardwood Floors
Once you have your wood flooring glued, you're ready to experience a great sense of accomplishment. If you did a good job of installing the hardwood floor with adhesive by method, not experience nearly as creaky floor syndrome as you would with other installation methods.
And for their sake, I hope you followed the instructions carefully and choose high quality soils. This is due to the substitution of a glued wood floor is not a task for amateurs. That is unless you pleasure destructive tendencies. You'll need some serious hammer, crow bar, and circular saw work, if you ever want to replace the glued wood floor.
Why choose Full Coverage Auto Insurance For Your Car
Monday, February 1, 2010
Kitchen Cabinets Type of Wood
When you start the purchase of kitchen furniture, the type of wood used is as important as the overall look or finish of the cabinets. Depending on whether you are buying RTA (ready to assemble), stock, semi custom or custom cabinets will have a huge impact on forest types that are available for you to choose from. Custom cabinets offer the largest selections of wood types, but also pay significantly more for them. Here is a list of types of wood that you can come across in your search for kitchen cabinets (listed in order of price)
Paint Grade
Paint Grade wood can actually consist of a wide range of types of wood. Most securities and mixed economy companies custom cabinet to apply a paint finish, including MDF and can be used instead of wood particles. The forests most common grade of paint will be of birch, poplar, or maple.
Oak
The oak is probably the most used wood for cabinets. Most contractor grade cabinets, and cabinets cheapest priced be of oak. Oak is available in more than 200 different species and is cultivated worldwide. The most common finish for oak cabinets is just a natural finish or honey. The oak is a strong, dense wood, which held up to everyday use and can accept stain well.
Pino
Pino comes in three different versions-white, yellow or ponderosa. White pine can be very easy to work with and will accept stain easily, while ponderosa will require special attention due to the resin that can still concentrate on the wood. Pine is ideal for creating a rustic feel to your home.
Maple
Maple is another type of wood used and can be found in a variety of species. This is probably the most common wood found in RTA cabinets because it grows in abundance in northern China and most RTA cabinets come from China. There are also over 10 species of maple that leave the U.S., so there are a variety of grains. Most maple is very easy to work with him and will accept stain easily. Maple finishes well in any color of a Finish Chestnut honey to glaze.
Cherry
Cherry is normally used in the average price of upper cabinets. The unique feature about Cherry is that with a light stain applied, it will actually get darker over time. As wood ages and is exposed to sunlight will change to reddish brown, most people associate with antique cherry furniture.
Bamboo
With the push to become eco-friendly, more and more cabinets are being designed using bamboo. Bamboo is an abundant plant that grows quickly. The biggest drawback is that bamboo has to be about another of plywood and bamboo plants do not grow thick enough to cut into boards. At this time, only find bamboo used by custom shops primarily on the West Coast
Mahogany
Mahogany creates a very rich look, and wood itself is reddish brown. Apart from exotic woods, this will be one of the more expensive options in the common wood types. Mahogany accepts stain very well, but not an overly strong wood.
If you are building a high-end kitchen or just updating a rental unit, there are a variety of wood types to select. Selecting a type of wood that hold the amount of use and abuse incurred is as important as the final product will look, so keep this in mind when shopping for kitchen cabinets.
Paint Grade
Paint Grade wood can actually consist of a wide range of types of wood. Most securities and mixed economy companies custom cabinet to apply a paint finish, including MDF and can be used instead of wood particles. The forests most common grade of paint will be of birch, poplar, or maple.
Oak
The oak is probably the most used wood for cabinets. Most contractor grade cabinets, and cabinets cheapest priced be of oak. Oak is available in more than 200 different species and is cultivated worldwide. The most common finish for oak cabinets is just a natural finish or honey. The oak is a strong, dense wood, which held up to everyday use and can accept stain well.
Pino
Pino comes in three different versions-white, yellow or ponderosa. White pine can be very easy to work with and will accept stain easily, while ponderosa will require special attention due to the resin that can still concentrate on the wood. Pine is ideal for creating a rustic feel to your home.
Maple
Maple is another type of wood used and can be found in a variety of species. This is probably the most common wood found in RTA cabinets because it grows in abundance in northern China and most RTA cabinets come from China. There are also over 10 species of maple that leave the U.S., so there are a variety of grains. Most maple is very easy to work with him and will accept stain easily. Maple finishes well in any color of a Finish Chestnut honey to glaze.
Cherry
Cherry is normally used in the average price of upper cabinets. The unique feature about Cherry is that with a light stain applied, it will actually get darker over time. As wood ages and is exposed to sunlight will change to reddish brown, most people associate with antique cherry furniture.
Bamboo
With the push to become eco-friendly, more and more cabinets are being designed using bamboo. Bamboo is an abundant plant that grows quickly. The biggest drawback is that bamboo has to be about another of plywood and bamboo plants do not grow thick enough to cut into boards. At this time, only find bamboo used by custom shops primarily on the West Coast
Mahogany
Mahogany creates a very rich look, and wood itself is reddish brown. Apart from exotic woods, this will be one of the more expensive options in the common wood types. Mahogany accepts stain very well, but not an overly strong wood.
If you are building a high-end kitchen or just updating a rental unit, there are a variety of wood types to select. Selecting a type of wood that hold the amount of use and abuse incurred is as important as the final product will look, so keep this in mind when shopping for kitchen cabinets.
Wednesday, January 27, 2010
How to Bending Wood
Bending wood is not the daunting task that seems at first sight. Depending on the degree of the curve, and if the curve is complex, there are a couple ways to bend wood.
First, you need a way to bend the wood around and clamp to maintain the thedesired. Most bent wood will have a degree of "elastic", so you have to create a form with an allowance for this. And unfortunately, there is no set formula for determining the degree of elastic recovery to a particular species of wood will produce. Springback is also influenced by the folding method used. That is, the steamed wood will spring,
or "straighten" more than wood that is laminated and glued. Another variable is the type of adhesive used in lamination.
As a general rule, the greater the curve, more wood spring back, making the allocation of a matter of trial and error at best.
As rolling thin strips is the easiest method, we begin with this process. The final thickness of the project will directly affect the size of the strips to be used, but overall, the best strip of use is about ¼ "thick. Bends may have to be made with 1 / 8" or thin strips, depending on the species of wood. Sounds like a lot of experimentation, but I'm afraid that is a necessary evil.
The form required for laminating can be as simple as a piece of pipe or as complex as a multi-station die. I like to keep things as simple as possible.
When laminating thin strips, can minimize effort and spring again soaking the strips before bending, and clamping the mold without sticking. Once dry, remove the mold, spread the glue and clamp back into the mold. Line pan with waxed paper to prevent sticking to the mold lamination.
When dipstick me, I do it in an open container, and depending on the wood and the size of the strips, I soak for 15 minutes at night. Also mix in half cup of fabric softener per gallon of water. I think it softens wood nearly as well as the fabric.
If the project is small, and free time in the queue is not a factor, I'll use poly-vinyl-acetate, or aliphatic resin glue. If I need more time to work, I'll use epoxy or resorcinol. I'm staying
far from epoxy resins, fast setting, however, because they rarely become hardened to the extent that the slow sets do. If you are using light colored wood, resorcinol dries to a reddish color that may be objectionable in a finished project.
When bending thin woods such as guitar parts, wood is commonly soaked as above, but bent over a hot bending template, either electric or hot with a propane torch. Fragile forests are supported on the outside of the curve with a thin band of stainless steel to help prevent cracking.
Green woods can be bent much the same way, or by heating the wood over hot coals or heat gun.
For projects where lamination is objectionable, or when the wood is going to bend compound curves, a steam box is the answer. One can be quite economically from PVC pipe, but needs to be supported to maintain the pipe deformation.
The pipe ends must be closed with a screw cap on at least one end, to allow access to the interior. Wrap the other end of the pipe with a DWV cut shirt, and attach a radiator hose to the side entrance and a new gas can be large enough to store enough water to function at work. The water can be heated with a hot plate or a propane burner.
Drill through the pipe slightly below center in two or three locations and insert dowels for the wood to rest. Steam can circulate freely around the wood, even for penetration. A hole about ½ "in diameter should be drilled in the lid off the steam
input to allow circulation. When you build the support framework for the steam box, field box
toward the steam inlet to allow condensation to return to the water source.
Rule of thumb is that the wood should be steamed fifteen minutes per inch of thickness, but again, some experiments will be necessary.
The wood needs to be placed in the way as quickly as possible, as the wood cools, it is harder to bend. Make sure your timber is at least two feet longer than the finished piece because it is almost impossible to bend a 3 / 4 "piece of wood that is less than a foot long, so the last foot will have to be cut
off after the wood is dry.
Clamp the wood securely, and leave it to cool completely. If you are working with several pieces, place in steam table, an approximately the interval required to place the piece in the manner and the clamp, and out of the box in the same order.
First, you need a way to bend the wood around and clamp to maintain the thedesired. Most bent wood will have a degree of "elastic", so you have to create a form with an allowance for this. And unfortunately, there is no set formula for determining the degree of elastic recovery to a particular species of wood will produce. Springback is also influenced by the folding method used. That is, the steamed wood will spring,
or "straighten" more than wood that is laminated and glued. Another variable is the type of adhesive used in lamination.
As a general rule, the greater the curve, more wood spring back, making the allocation of a matter of trial and error at best.
As rolling thin strips is the easiest method, we begin with this process. The final thickness of the project will directly affect the size of the strips to be used, but overall, the best strip of use is about ¼ "thick. Bends may have to be made with 1 / 8" or thin strips, depending on the species of wood. Sounds like a lot of experimentation, but I'm afraid that is a necessary evil.
The form required for laminating can be as simple as a piece of pipe or as complex as a multi-station die. I like to keep things as simple as possible.
When laminating thin strips, can minimize effort and spring again soaking the strips before bending, and clamping the mold without sticking. Once dry, remove the mold, spread the glue and clamp back into the mold. Line pan with waxed paper to prevent sticking to the mold lamination.
When dipstick me, I do it in an open container, and depending on the wood and the size of the strips, I soak for 15 minutes at night. Also mix in half cup of fabric softener per gallon of water. I think it softens wood nearly as well as the fabric.
If the project is small, and free time in the queue is not a factor, I'll use poly-vinyl-acetate, or aliphatic resin glue. If I need more time to work, I'll use epoxy or resorcinol. I'm staying
far from epoxy resins, fast setting, however, because they rarely become hardened to the extent that the slow sets do. If you are using light colored wood, resorcinol dries to a reddish color that may be objectionable in a finished project.
When bending thin woods such as guitar parts, wood is commonly soaked as above, but bent over a hot bending template, either electric or hot with a propane torch. Fragile forests are supported on the outside of the curve with a thin band of stainless steel to help prevent cracking.
Green woods can be bent much the same way, or by heating the wood over hot coals or heat gun.
For projects where lamination is objectionable, or when the wood is going to bend compound curves, a steam box is the answer. One can be quite economically from PVC pipe, but needs to be supported to maintain the pipe deformation.
The pipe ends must be closed with a screw cap on at least one end, to allow access to the interior. Wrap the other end of the pipe with a DWV cut shirt, and attach a radiator hose to the side entrance and a new gas can be large enough to store enough water to function at work. The water can be heated with a hot plate or a propane burner.
Drill through the pipe slightly below center in two or three locations and insert dowels for the wood to rest. Steam can circulate freely around the wood, even for penetration. A hole about ½ "in diameter should be drilled in the lid off the steam
input to allow circulation. When you build the support framework for the steam box, field box
toward the steam inlet to allow condensation to return to the water source.
Rule of thumb is that the wood should be steamed fifteen minutes per inch of thickness, but again, some experiments will be necessary.
The wood needs to be placed in the way as quickly as possible, as the wood cools, it is harder to bend. Make sure your timber is at least two feet longer than the finished piece because it is almost impossible to bend a 3 / 4 "piece of wood that is less than a foot long, so the last foot will have to be cut
off after the wood is dry.
Clamp the wood securely, and leave it to cool completely. If you are working with several pieces, place in steam table, an approximately the interval required to place the piece in the manner and the clamp, and out of the box in the same order.
Monday, January 11, 2010
How Fitting a Wooden Floor
Wood floors have been popular for decades and there are still those who prefer a natural and clean their homes. There are several advantages to having a wood floor because they have been very popular. An important advantage of this type of flooring is that it is easy to place at home without having to call a specialist.
Homeowners who are planning to fit wooden flooring in your home on your account must follow the steps listed below:
Before putting the wooden floor is essential to set a lower layer of the plant in which the wooden floor should be placed. Underlying can be bought at any hardware store or floors. We must ensure that the base layer is made of good quality to achieve the desired results. Usually made of foam and is to be set out in sections in the area where the soil is to be placed.
The first step in establishing a wood floor is to prepare the room or area where the soil is established. It is important to ensure that the floor is even and level. All protruding nails and other must be eliminated. Once the surface is properly prepared, the laminates or wooden floor can be established.
Boards can also be arranged in a staggered and irregular use half of a table instead of the whole to be better future and to avoid any obvious line on the floor. In most cases, details and instructions will be in the shops with wooden boards.
In areas where there is high humidity or moisture, the base layer is made of a moisture-proof material to avoid damage due to moisture in the soil.
Once the base layer is provided, the floor can be adjusted. Start from one corner of the room and leave a little space between the first row of tables and the wall. Once the first row of wooden planks placed on the floor, start with the second.
A complete row of boards should be equipped and then lifted out properly before they can join the first row of tables.
Continue to place the tables in the same way, completing one row before moving to the next until the entire floor. Once done, any strange or outside angles should be measured, cut and positioned to occupy the space. Along the sides of the room, an expansion joint should be maintained between tables and the wall. This gap can be covered with a round edge or a socket.
For a wood floor in the home is not very difficult, especially because in most cases, detailed instructions are provided by manufacturers.
Homeowners who are planning to fit wooden flooring in your home on your account must follow the steps listed below:
Before putting the wooden floor is essential to set a lower layer of the plant in which the wooden floor should be placed. Underlying can be bought at any hardware store or floors. We must ensure that the base layer is made of good quality to achieve the desired results. Usually made of foam and is to be set out in sections in the area where the soil is to be placed.
The first step in establishing a wood floor is to prepare the room or area where the soil is established. It is important to ensure that the floor is even and level. All protruding nails and other must be eliminated. Once the surface is properly prepared, the laminates or wooden floor can be established.
Boards can also be arranged in a staggered and irregular use half of a table instead of the whole to be better future and to avoid any obvious line on the floor. In most cases, details and instructions will be in the shops with wooden boards.
In areas where there is high humidity or moisture, the base layer is made of a moisture-proof material to avoid damage due to moisture in the soil.
Once the base layer is provided, the floor can be adjusted. Start from one corner of the room and leave a little space between the first row of tables and the wall. Once the first row of wooden planks placed on the floor, start with the second.
A complete row of boards should be equipped and then lifted out properly before they can join the first row of tables.
Continue to place the tables in the same way, completing one row before moving to the next until the entire floor. Once done, any strange or outside angles should be measured, cut and positioned to occupy the space. Along the sides of the room, an expansion joint should be maintained between tables and the wall. This gap can be covered with a round edge or a socket.
For a wood floor in the home is not very difficult, especially because in most cases, detailed instructions are provided by manufacturers.
Sunday, January 10, 2010
Laminate Wood Flooring
Of all the laminate flooring materials on the market, laminate wood flooring is the most popular due to natural occurrence of materials and durability. With materials like bamboo and cork, the possibility of the surface can be dented, while plywood flooring offers more resistance to heavy furniture sitting in one place for extended times and heavier elements that sank into the ground. Their general appearance makes it more attractive to a wider range of use.
Once you have installed a real wood floor, you will need sanding, staining with the desired color and then coated with a protective finish, which can take several days. This means that furniture and Ensuring that the room will be delayed. When installing laminate wood flooring, the room we can use the same day without fear of harming the finish.
The materials used are layered laminate flooring using special glues and pressure to keep the layers together. Without the proper process, layers can be separated and curl, as do some of the cheapest on offer laminate flooring, but the use of laminate wood flooring can still be considerably less expensive than trying to install a real wood floor. Installation can only be reduced significantly and when considering the termination of real wood, many decide Laminate wood flooring offers the best option for your home.
Election of strength over aesthetics
The density of the material layer will also protect the wood laminate flooring become dented or torn. The maintenance of laminate wood flooring is relatively simple, but keep in mind that any gross residue as sand or kitty litter has the potential to be filed in shoes, scratching the top layer of the plant.
One of the main reasons people opt for laminated wood flooring is also resistant to many other materials. However, it should be noted that not all laminate wood floors are the same. The number of laminated layers, the type of bonding process used to keep the layers from curling and protective finish is applied to the outermost layer determines the overall strength of the flooring material.
Press sweep the dust with a mop and quick spill cleanup will help keep the wood laminate floor looking new for years. It also advises the use of carpet near the doors to help catch any of the products aggregates that could end up damaging the soil surface.
Once you have installed a real wood floor, you will need sanding, staining with the desired color and then coated with a protective finish, which can take several days. This means that furniture and Ensuring that the room will be delayed. When installing laminate wood flooring, the room we can use the same day without fear of harming the finish.
The materials used are layered laminate flooring using special glues and pressure to keep the layers together. Without the proper process, layers can be separated and curl, as do some of the cheapest on offer laminate flooring, but the use of laminate wood flooring can still be considerably less expensive than trying to install a real wood floor. Installation can only be reduced significantly and when considering the termination of real wood, many decide Laminate wood flooring offers the best option for your home.
Election of strength over aesthetics
The density of the material layer will also protect the wood laminate flooring become dented or torn. The maintenance of laminate wood flooring is relatively simple, but keep in mind that any gross residue as sand or kitty litter has the potential to be filed in shoes, scratching the top layer of the plant.
One of the main reasons people opt for laminated wood flooring is also resistant to many other materials. However, it should be noted that not all laminate wood floors are the same. The number of laminated layers, the type of bonding process used to keep the layers from curling and protective finish is applied to the outermost layer determines the overall strength of the flooring material.
Press sweep the dust with a mop and quick spill cleanup will help keep the wood laminate floor looking new for years. It also advises the use of carpet near the doors to help catch any of the products aggregates that could end up damaging the soil surface.
Saturday, January 9, 2010
Tip Install Brazilian Hardwood Flooring
Nothing can compare to the exquisite beauty and elegance of a Brazilian hardwood floor. The way it is installed on the ground is vital for its aesthetics and ideally a professional installation is recommended. In general, retailers recommend your favorite wood of professional customers. However, if you are a DIY people who like doing things on their own and are very interested in home improvement techniques, you'll find wood floors are not as difficult to design. Although the task may seem overwhelming at first, once you start with it, although with proper guidance and adherence to proper procedure, you will find things literally fall into place.
You will have to fix first for the complete set of tools and equipment required for the job - instead of buying every single tool (a very expensive course of action in itself), you can borrow. Be prepared to spend about $ 200 at this point. Once you have the tools in hand you can start your job but make sure you have an installation guide, or someone in person, to walk through the entire project. Although not the most complex of all jobs, mistakes are easy to do, while installing a hardwood floor and can result in dramatically lower results - something you do not want.
Without going into details of land during the installation process, here are some checkpoints that you have to be taken into account:
You must first establish the base layer on which the current Brazilian hardwood floor has been installed.
The current installation is relatively simple and a great satisfaction because it gives a sense of achievement and progress in this long and tedious project.
The final part to finish the plant is actually the hardest part - it involves sanding, staining and clear coating. Be prepared to break new work in this part of the project.
Some tips you should make a note of while going through the whole process are:
The hardwood boards that manufacturing offers access to contain short pieces that seem to go well in any area. These pieces are best kept to less visible areas such as recesses, closets, etc.
Make sure you are satisfied with the design of the pieces, while the floor of shelves for himself, and make adjustments there and then - as it will be difficult to make changes later.
Be careful not to take any of the tools have sharp edges in contact with the ground.
For a Brazilian wood floor is long and protracted process, particularly if you want to design a floor with an edge. Be prepared to spend at least a weekend if they do not want a border, and a series of weekends for a flat with an edge. Also, bear in mind a few more days of sanding and polishing the floor.
However, at the very end, you will have excellent Brazilian hardwood floor instead of his home and a feeling of fullness in your heart - nothing in this world can beat that.
You will have to fix first for the complete set of tools and equipment required for the job - instead of buying every single tool (a very expensive course of action in itself), you can borrow. Be prepared to spend about $ 200 at this point. Once you have the tools in hand you can start your job but make sure you have an installation guide, or someone in person, to walk through the entire project. Although not the most complex of all jobs, mistakes are easy to do, while installing a hardwood floor and can result in dramatically lower results - something you do not want.
Without going into details of land during the installation process, here are some checkpoints that you have to be taken into account:
You must first establish the base layer on which the current Brazilian hardwood floor has been installed.
The current installation is relatively simple and a great satisfaction because it gives a sense of achievement and progress in this long and tedious project.
The final part to finish the plant is actually the hardest part - it involves sanding, staining and clear coating. Be prepared to break new work in this part of the project.
Some tips you should make a note of while going through the whole process are:
The hardwood boards that manufacturing offers access to contain short pieces that seem to go well in any area. These pieces are best kept to less visible areas such as recesses, closets, etc.
Make sure you are satisfied with the design of the pieces, while the floor of shelves for himself, and make adjustments there and then - as it will be difficult to make changes later.
Be careful not to take any of the tools have sharp edges in contact with the ground.
For a Brazilian wood floor is long and protracted process, particularly if you want to design a floor with an edge. Be prepared to spend at least a weekend if they do not want a border, and a series of weekends for a flat with an edge. Also, bear in mind a few more days of sanding and polishing the floor.
However, at the very end, you will have excellent Brazilian hardwood floor instead of his home and a feeling of fullness in your heart - nothing in this world can beat that.
Tuesday, January 5, 2010
Hardwood Floor Installation
Whether you buy a wood floor discount or a more expensive type, you should know that can tackle the job on their own, because the installation of wood flooring is not really that difficult. However, if you want to install wood floor to arrive quickly and without problems - not to mention profitable as possible - then you should know that there are some steps you will need to follow.
Gather materials
Of course, as you would any other job, the first thing you have to do is gather the materials together. There are some elements that are necessary and others are optional. You need an angle nailer, square, chalk line, hammer, table saw, cutting saw, nail gun and use block and pull bar.
Choose your style
The next step in the process of installing hardwood flooring is to choose your style. What type of wood you think will give the right look for your space? Also remember that if you have the wood delivered to your home, you should be prepared to deliver a very large and heavy stack of wood, especially if you are doing more than one room in your home.
Getting Started
You can start with the installation of hardwood floor. For proper installation of hardwood floor you will want to start by snapping a chalk line on the ocean floor. This gives you an idea of where the wood is going to go. Always measure twice, once established, so as not making a mistake.
Next on the installation of hardwood floor, you need to start nailing the wood, and then you want to stain with any color of the stain you want. Different shades of stain will leave you with a different effect. The darker spots are more elegant and majestic, while the spots are lighter more casual.
Always check your work as it progresses, so if you end up making a mistake can be corrected immediately instead of realizing the end and having to go all the way back to the beginning.
The benefits offered by a wood floor are truly enormous, and if there is any supreme favorite type of wood flooring is definitely hard. Not only is rugged and affordable, but there are so many different options in terms of color and style that never definitely missing here.
Gather materials
Of course, as you would any other job, the first thing you have to do is gather the materials together. There are some elements that are necessary and others are optional. You need an angle nailer, square, chalk line, hammer, table saw, cutting saw, nail gun and use block and pull bar.
Choose your style
The next step in the process of installing hardwood flooring is to choose your style. What type of wood you think will give the right look for your space? Also remember that if you have the wood delivered to your home, you should be prepared to deliver a very large and heavy stack of wood, especially if you are doing more than one room in your home.
Getting Started
You can start with the installation of hardwood floor. For proper installation of hardwood floor you will want to start by snapping a chalk line on the ocean floor. This gives you an idea of where the wood is going to go. Always measure twice, once established, so as not making a mistake.
Next on the installation of hardwood floor, you need to start nailing the wood, and then you want to stain with any color of the stain you want. Different shades of stain will leave you with a different effect. The darker spots are more elegant and majestic, while the spots are lighter more casual.
Always check your work as it progresses, so if you end up making a mistake can be corrected immediately instead of realizing the end and having to go all the way back to the beginning.
The benefits offered by a wood floor are truly enormous, and if there is any supreme favorite type of wood flooring is definitely hard. Not only is rugged and affordable, but there are so many different options in terms of color and style that never definitely missing here.
Monday, January 4, 2010
Why use Rug Pads for your Wood Floors
Wood floors wood may be strong but susceptible to damage caused by everyday use. Some common causes of damage to wood floors are raw backs touch the floor carpets or furniture legs, causing scratches and dents. These need not be problems if you use the rug pad under your carpet.
A rug pad quality has many functions. Extends the life of any carpet. Property also offers a slip in fall is a problem. A rug pad can add comfort and sound insulation. Finally, a rug pad acts as a barrier between the carpet and furniture and wooden floors, therefore, protect and prolong the life of all wood and wood floors.
For all carpets must be a rug pad. Now, let's look at the best choice in carpet pads offer the best protection for wood floors. Since there are non-slip pads available, I like the sound for the best protection. There are strong and solid jute rug pads and the combination of rubber carpet pads. The quality versions of these solid-slip pads are dense enough to withstand heavy furniture indentations, to protect wooden floors.
There are the skid pad with open weave, or holes, as they are available, whether the protection of soil is your main concern, the best options are solid tablets. The non-skid rug pads are fine holes to provide a non-slip feature but thay are not too heavy or strong enough to withstand the weight of many furniture possibly damage your hardwood floor.
Solid rug pads are better protected than 1 / 4 inch thick or thicker. These pads act as a solid barrier between the carpet and floors and generally avoid much damage. Carpet Corner Pad offers two types of these pills are both solid and very dense wood to protect the floor. You can find other places that offer a solid carpet and cushions.
For the best in protecting the wooden floor where they have rooms with rugs, choose the right rug pad solid and avoid significant damage to your floors. The small investment now will save you a small fortune possible, floor repairs later.
A rug pad quality has many functions. Extends the life of any carpet. Property also offers a slip in fall is a problem. A rug pad can add comfort and sound insulation. Finally, a rug pad acts as a barrier between the carpet and furniture and wooden floors, therefore, protect and prolong the life of all wood and wood floors.
For all carpets must be a rug pad. Now, let's look at the best choice in carpet pads offer the best protection for wood floors. Since there are non-slip pads available, I like the sound for the best protection. There are strong and solid jute rug pads and the combination of rubber carpet pads. The quality versions of these solid-slip pads are dense enough to withstand heavy furniture indentations, to protect wooden floors.
There are the skid pad with open weave, or holes, as they are available, whether the protection of soil is your main concern, the best options are solid tablets. The non-skid rug pads are fine holes to provide a non-slip feature but thay are not too heavy or strong enough to withstand the weight of many furniture possibly damage your hardwood floor.
Solid rug pads are better protected than 1 / 4 inch thick or thicker. These pads act as a solid barrier between the carpet and floors and generally avoid much damage. Carpet Corner Pad offers two types of these pills are both solid and very dense wood to protect the floor. You can find other places that offer a solid carpet and cushions.
For the best in protecting the wooden floor where they have rooms with rugs, choose the right rug pad solid and avoid significant damage to your floors. The small investment now will save you a small fortune possible, floor repairs later.
Sunday, January 3, 2010
Installing Wood Floors
Wood Flooring is a great option for owners and enthusiasts of DIY projects. They are easy to install, comes prefinished and are not available in local hardware stores or shops for rent at an affordable price. Engineered wood floors come in many different types, including wood, cherry, oak and bamboo. They come pre-finished, stained and coated. Manufactured complement together, a homeowner with no experience in installing hardwood floors or finishing will be able to install this type of wood floors easily and correctly. Engineered wood flooring can be installed using nail, glue down or installed as a floating floor.
Laminate Hardwood Floors looks great and costs less. A laminate flooring offers a range of different styles including many popular types of wood. One benefit of engineered and laminate flooring is the ability to install a floating floor. A floating floor allows you to install the new floor flat above his age, without glue or nails due to the ability of soils to snap together. With a low cost and high durability, laminate wood flooring is a great option for homeowners on a tight budget.
Traditional wood floors come unfinished. Should be set up underground. One problem with traditional wood floors is that moisture can cause the wood to expand and contract. Before installation make sure the timber has been adjusted to moisture level of your home. Homeowners who are looking to install traditional wood flooring needs more experience. Preparation, installation, sanding and finishing ensures meticulous steps that if done incorrectly and damaging the floor.
Laminate Hardwood Floors looks great and costs less. A laminate flooring offers a range of different styles including many popular types of wood. One benefit of engineered and laminate flooring is the ability to install a floating floor. A floating floor allows you to install the new floor flat above his age, without glue or nails due to the ability of soils to snap together. With a low cost and high durability, laminate wood flooring is a great option for homeowners on a tight budget.
Traditional wood floors come unfinished. Should be set up underground. One problem with traditional wood floors is that moisture can cause the wood to expand and contract. Before installation make sure the timber has been adjusted to moisture level of your home. Homeowners who are looking to install traditional wood flooring needs more experience. Preparation, installation, sanding and finishing ensures meticulous steps that if done incorrectly and damaging the floor.
Saturday, January 2, 2010
How Care Hardwood Floors
Hardwood floors are an investment to add much more beautiful than to walk home from a polished surface. Known for its durability, versatility and bright colors, wood floors have been a popular addition to the homes of many different styles. Solid wood can be expensive, but should be considered an investment in your home, as will likely increase the resale value of your property.
Wood floors are exactly as they sound - from hardwoods. As such, they will withstand the regular use softwoods can not. That does not mean that they will take a beating, however. They require special maintenance to keep looking beautiful for years, and indeed, with wood floors care law has been known that the last centuries.
Be careful to avoid stains from surfaces
Do not let dirt, dust and sand settle to the floor for long. As it builds up, walking on the earth or sand can scratch off the surface or shine. The animal hair and other fibers are strong enough to do the same. Water spills should be cleaned immediately with a soft cloth or wood deformation might occur. Moving the furniture, the use of felt under pressure points, or pick up the furniture in place of thrust and drag around to prevent scratches and dents. They also use curtains, blinds or sheer curtains to direct sunlight, which can whiten your story in the long term.
Regular maintenance
Maintaining your hardwood floor is easier than you might think. No need for annual sanding and refinishing, but regular sealing treatment is a good idea. For weekly cleaning, select a solution made of wood flooring, Laminate no. This is very important to avoid damaging the wood surface coat of sealer or existing. For rooms that are not frequented, a simple dry cleaning to remove dust may be sufficient. A soft towel is ideal for this work, adding a splash of wood can increase the brightness and added protection.
Special Considerations
Wood floors are a welcome addition to any home, but still not practical for many home environments. Soils of this type is not recommended when the humidity is a problem, or in rooms with constant humidity. Moreover, households with many pets may have difficulty keeping the soil free of scratches and stains that can result from pet nails, dandruff of the bathrooms or accidents. High heels, sneakers and gross domestic games can also damage or slightly sea surface wooden floors, so be sure to keep these things in mind when deciding what type of floor surface best suits your home .
Wood floors are exactly as they sound - from hardwoods. As such, they will withstand the regular use softwoods can not. That does not mean that they will take a beating, however. They require special maintenance to keep looking beautiful for years, and indeed, with wood floors care law has been known that the last centuries.
Be careful to avoid stains from surfaces
Do not let dirt, dust and sand settle to the floor for long. As it builds up, walking on the earth or sand can scratch off the surface or shine. The animal hair and other fibers are strong enough to do the same. Water spills should be cleaned immediately with a soft cloth or wood deformation might occur. Moving the furniture, the use of felt under pressure points, or pick up the furniture in place of thrust and drag around to prevent scratches and dents. They also use curtains, blinds or sheer curtains to direct sunlight, which can whiten your story in the long term.
Regular maintenance
Maintaining your hardwood floor is easier than you might think. No need for annual sanding and refinishing, but regular sealing treatment is a good idea. For weekly cleaning, select a solution made of wood flooring, Laminate no. This is very important to avoid damaging the wood surface coat of sealer or existing. For rooms that are not frequented, a simple dry cleaning to remove dust may be sufficient. A soft towel is ideal for this work, adding a splash of wood can increase the brightness and added protection.
Special Considerations
Wood floors are a welcome addition to any home, but still not practical for many home environments. Soils of this type is not recommended when the humidity is a problem, or in rooms with constant humidity. Moreover, households with many pets may have difficulty keeping the soil free of scratches and stains that can result from pet nails, dandruff of the bathrooms or accidents. High heels, sneakers and gross domestic games can also damage or slightly sea surface wooden floors, so be sure to keep these things in mind when deciding what type of floor surface best suits your home .
Subscribe to:
Posts (Atom)